This is Phil's lockdown project March-June 2020, a full FHSS R/C outfit using really cheap NRF24L01 RF modules.
This update is dated Feb 2026 and has revised receiver code with some functional updates, transmitter code untouched.
Rather than transmitter model-memories, we have appropriate reversing and mixing retained inside each rx.
Hopping logic revised for clarity & ease of maintenance, incrementing park channel. Compatible with existing 4ch/5ms tx.

Follow the story here: http://mode-zero.uk/viewtopic.php?f=42&t=971
Also the Single-Channel Emulation version: http://mode-zero.uk/viewtopic.php?f=42&t=968

Configuration:
There are two vitally important config lines in the receiver, and two corresponding lines in the transmitter.
These need to be edited but the tx and rx configs must match. For pipOut and pipeIn I suggest we use the last
five digits of our phone numbers, this will be sufficiently unique in our small group.  For mychannels[] choose
sixteen channel numbers between 0 and 125, spread randomly and at least two apart - for example:

const byte pipeOut[] = "12345";   // last 5 digits of your phone number, 'pipeIn' in receiver must be the same 
const byte mychannels[] = {5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 78, 75, 80};  // choose 16 FHSS well-spread hopping channels

Transmitter:
A simple four channel RC encoder for the NRF24L01 with proper FHSS hopping, one packet every 5ms.  Easily expanded.
Uses sixteen RF channels well spread through the band and a unique identifier.  Use a high-power (NRF24L01+PA+LNA) module for tx.
The encoder is based on the 7ch+S/C, and has single-channel escapement emulation mix, Vtail, Elevons, minute-minder, 
remote failsafe setting, throttle lock, variable expo & rates, +-400 +trim range,  minute-minder, etc
Calibration - center trims, hold the s/c button in, switch on, still holding button move all controls to extremes.
Center all controls including throttle. Release button.  At this point the throttle-lock warning should chirp because the throttle is centred.
Do not switch off during calibration, the calibration values cant be saved if the set has been switched off!
Throttle response can optionally be made non-linear during calibration by 'centering' the throttle stick to say 2/3 rather than to neutral stick.
Variable expo & rates on Futaba ch1, 2 & 4, ditto JR ch2, 3 & 4. Elevon mixer on Futaba ch1 & ch2, JR ch2 & 3, 75% aileron, 25% elevator or 50:50 for V-tails
Mixer option can only be changed on power-up (avoids accidentally switching during flight).  Single-channel emulation mix, compound only, two speed options
Servo reversing by holding sticks over on power up (saved to eeprom).
Auto and manual throttle-lock with warning.

Receiver: (updated Feb 2026)
Can be an RF-Nano which makes assembly straightforward, or separate 5v or 3v3 Promini and NRF24L01. The rx code suits either.
Has programmable failsafe on all functions, set either by a link on D8 at the rx or a button on the tx. When set with rx pin, servo wiggles to confirm its stored.
If failsafe is not set, loss of signal reverts to defaults - low throttle and neutral controls.
Power can be a 1S Li-Ion or a 5v BEC to Vcc and servo positives, or a higher voltage to Vin. Dont exceed 5v on Vcc. All negs are common.
Must add a filter capacitors (say 100uF & 1nF in parallel) across 0v and 3v3 on both tx and rx otherwise the NRF24L01 can misbehave.
Servo signals on pins D2, D3, D4, D5. Optional 5v LED pos to A0, neg to A1 flashes every 20 packets, stays on if in failsafe.
Individual receivers contain any channel mixers such as elevon etc and rx retains all reverse settings - to reverse a channel,
power on the transmitter, hold appropriate stick over, switch on receiver. Give it a second and reversing will be saved within the rx.

Diagram and documentation on http://www.singlechannel.co.uk see Archive page
If you use this software in whole or in part please acknowledge its source - Phil_G on most forums, philg@talk21.com  http://www.singlechannel.co.uk
Thanks to Mike Kitchen and the late Dave Burton for their improved expo maths, and to Werner L for his encouragement.

Cheers
Phil_G

